How to make a smartphone stand with your own hands: a review of the best ideas, as well as step-by-step instructions

Who among us doesn’t like to watch TV series or movies while cooking something in the kitchen or eating? The phone is not a laptop; it will lie flat on the table. It is, to put it mildly, uncomfortable to look at something like that. You can buy a special stand to secure your phone in a vertical position, or you can make it yourself from scrap materials. For example, these could be ordinary office clips.

How to make your own phone stand from paper clips

There are several ways to make a stand from clamps. Let's talk about simple and more complex ones.

Method with two clamps of different sizes

What you will need to make: one large clamp and a second smaller one - medium or small. Nothing more is needed.

Buy two clamps of different sizes

You only need to connect these two office tools in a certain way:

1. We turn the smaller clamp handles in the opposite direction. We connect them with each other.
2. We place the two connected handles in a large clamp.

   Insert the handles of the small one into the large clamp

3. We put a homemade stand on the table, and put the phone on it. Adjust the base of the small clamp if necessary.

   Place the phone on the ready-made stand

The clamps may be the same size. Then you just need to connect them differently: bend the handles of one clamp in the same way and connect them, but place them in the other clamp, not them, but the base of the clamp itself. Place the phone between the handles of the attached binder.

The stand can be made from two clamps of the same size

Another method using clamps of the same size. We will additionally need a sheet of paper in it. Its width will be equal to the width of the clamps, and its length will be the height of your phone. Simply clamp the edges of the paper with clamps on both sides. The lower handles of the binders will be the base of the stand, and the upper ones will be the holders. Place your phone between the top handles.

Attach two clips to a piece of paper

One clamp method

If you only have one clamp, you can still make a stand out of it. The advantage of this option is that you can attach this stand to any object that will “take” the clip.

Additionally, you also need insulation from the wires (for the previous methods it can also be used). This is optional, but it is advisable to ensure that the paperclip does not scratch the phone. You also need a small piece of fabric and an elastic band (any kind, maybe a small one for hair or several stationery ones).

Insulation from the cable is needed to soften the landing of the phone on the stand

So, let's start assembling the stand:

1. Carefully remove the handles from the base of the clamp and bend their upper round parts inward using pliers (use a piece of fabric so as not to scratch the handles of the clamp). These folds will help securely secure the phone to the stand.

   Remove the handles from the clamp

2. We put the insulation on the handles, and insert the handles themselves back into the base of the clamp.

   Insert the wire into the insulation

3. If desired, we put the insulation (already cut) on the lower edges of the clamp base.

   Attach the handles to the base of the clamp

4. We fasten the handles of the clamp with an elastic band at the base of the stationery tool.

   Use a regular hair tie to secure the handles.

5. We insert it into the phone between the handles.
   Secure your phone to the finished cradle

Video: several options for phone stands made from office clips

You can build a phone stand from ordinary office clips. In this case, you can have at least two clamps, at least one. The easiest way is to take two clamps of different sizes and insert the connected handles of one binder into the base of the other clamp.

• Ekaterina Vasilyeva
• Print

Source: https://kompkimi.ru/sovety/eto-polezno-znat/podstavka-dlya-telefona-iz-zazhimov

What to consider when choosing a stand type

When planning to assemble a phone holder, you need to understand:

• whether the structure is planned for temporary or permanent use;
• does its external aesthetics matter?
• will the material support the weight of the device;
• How safe is the option for the phone and its owner;
• If we are talking about a complex and intricate stand, it is important to understand whether there is enough time and skill to implement the plan.

Having decided on these parameters, you can begin to select the optimal model.

To summarize: there are several ways to make a phone holder for your home or office. The choice of material and type of construction is determined by the parameters of the phone, as well as the preferences of its owner.

Phone holder on the table: 7 super quick options

Merilyn

1712 0 0

The stand is convenient for viewing videos and photos on your phone

A phone stand is a convenient gadget: it frees your hands while reading, viewing images, videos, and playing games. There are many ways to quickly make phone holders. I offer the most comfortable and lightest ones - from scrap materials.

Option 1. Stationery binders

There are several ways to make a holder from office clips/clips. They provide stability. You can take any quantity for production.

If you construct a mount from several clamps, the stand turns out to be convenient, but cumbersome. I'll tell you how to make a stand from a minimum number of clips.

1. One clamp. To do this, you need to make a “bed”: slightly bend the metal part of the clip towards the installation of the phone.

Bent eye of the clip

1. Stand option for the lazy. You don't need to do anything, just find one clip. Pinch the edge of the case on one side and place the phone on the table.

The location is convenient for placing the phone horizontally

1. Two clips and a strip of thick paper. The size of the sheet of paper corresponds to the size of your smartphone.

Option for video shooting, as the stand is stable and its tilt is adjustable

1. Two clamps . They are fastened so that one remains open. For reliable fixation, the lower, open end is bent or a piece of pencil eraser is inserted into it.

The ear of the clip needs to be bent

1. From two clamps you can make a stand in 5 seconds . Place the small pen in the open large clip. Close the clamp and the stand is ready. It is compact, does not take up much space, and can be carried in your pocket.

I offer a detailed description of the steps to make the simplest smartphone stand. The table shows the steps.

Paper or cardboard option

If you have origami skills, you can turn a sheet of paper into a phone holder with your own hands. To do this, 4 folds are left on the A4 sheet, dividing the space into 4 even transverse stripes. Then the sheet unfolds and is visually divided in half. Make 2 new quarter folds on each edge.

The workpiece is turned over to the other side, where the edge is folded, making up 1/8 of the length of the sheet. All that remains is to turn the sheet over, bend it first along the longitudinal folds, and then along the transverse ones. The result is a triangle with a pocket for your phone.

To make a tablet stand with your own hands, you should use cardboard. 3 rectangular parts are cut from this material. In two of them there are holes for the holder. Then the elements are bent and glued in the shape of a triangle. The seams are additionally fixed with binders.

How to make a phone stand from simple objects

Don't want to hold your phone while watching a video, but it keeps falling over? There are several simple lifehacks with available tools that will make your wish come true. Stationery clips, old cassette tapes, sunglasses and other small items will help free your hands and protect your device from damage.

Stands made from paper clips and paper clips

You will need one large paper clip and one smaller one. Fold the tabs off the small clip and place them inside the other one.

Now place the structure on the table with the small clamp facing you. Ready! Place the smartphone horizontally in the resulting corner.

Another way:

1. Straighten the ears of the large clip.
2. Hook them with a small clip so that the two objects are perpendicular to each other.
3. Now straighten the second clamp. Its ears will be the support, and the body will be the wall of the stand.
4. At the first (large) clip, you need to bend the body a little to create a convenient angle for placing the phone there.
5. If the device slips a lot without a silicone case, simply stick a piece of adhesive tape on the bottom of the stand.

A large paper clip will also help. Straighten it to a right angle, bend the shorter part a little with pliers so that the smartphone holds. The stand is ready. You can use two paper clips for better stability.

Cassette coasters

Remember the old audio cassette boxes? If you happen to have such a thing lying around, it will become a convenient stand for your phone! Just open it, place it with the recess for the cassette down, and place the device in the slot.

Other ideas

What else can you make a phone stand from, available tools:

1. Sunglasses. Fold the arms and secure your smartphone in them. The glasses should be large so that the smartphone does not overweight and the structure does not fall.
2. Use non-slip car mats. Place them under the phone, and use any sufficiently large object as a stand: a box, a glass, etc.
3. Take 6-8 household clothespins. They should be smooth, large, and made of strong material. You'll also need a pencil. Clamp the pencil with clothespins, leaving a small distance in the center equal to approximately half the length of the device. Now place the clothespins with the pencil on the table, with the inner clothespins facing up. They will serve as a phone stand. The remaining clothespins hold the structure in place.
4. Build a phone stand from a regular sheet of thick paper (for printing) and a stapler.
5. The smartphone can be secured to any handy object using a stretchy elastic band.
6. Take an unnecessary case and glue it with double tape (only tightly) to a box or other item. Just insert your phone into the design when you are going to watch something.

Method 3: Using cardboard

1.Flatten 1 cardboard toilet paper tube. Take the empty cardboard tube that used to hold toilet paper. Lay it flat on a flat surface and press down on the center to flatten the cardboard.

• Alternatively, you can use a cardboard coffee cup sleeve.

2. Draw a line down the middle of the cardboard tube. Orient the flattened tube so that the short edges are at the top and bottom. Use a ruler to find the center of the cardboard tube. Draw a horizontal line through the tube with a permanent marker or pencil.

3. Draw a line from the center point to the corner of the cardboard tube. Use a ruler to find the middle of the tube along the center line you just drew. Connect this point to any corner of the pipe by drawing a diagonal line.

• It doesn't matter which angle you choose.

4. Mark the thickness of your phone along the center line. Measure the thickness of your phone using a ruler. Make perpendicular marks for this measurement along the center line. Start the measurement at the center point and end on the side opposite the diagonal line. Draw a perpendicular line 1⁄2 inch (1.3 cm) down for each mark away from the diagonal line.

• Phones typically range from 1⁄4–1⁄2 inches (0.64–1.27 cm) in thickness.

5. Cut along the lines you drew on the cardboard tube. Remove the smaller piece by cutting off the corner piece and leave the larger piece. Make 2 small cuts along each line indicating the depth of your phone.

• Hold the cardboard tube firmly as you cut it to ensure it stays flat.

6. Open the cardboard tube and lean the phone against the high back. Place your fingers into the cardboard tube to gently open it into a round shape. Place the round base on a flat surface. Lay the phone horizontally across the cuts, with the taller piece of cardboard at the back and the shorter piece at the front.

• Your phone will be inserted into the handset crosswise.
• You can leave the cardboard tube as is or decorate it with a permanent marker if you like.

How to make a phone stand from a paper clip

Sanya Nestruev · 05/21/2019

In our article today we will talk about how to make a phone stand out of a paper clip. This is a very useful life hack, especially when you don’t have a book case with such a function. Moreover, all the materials that we need are in any home and there will be no problems with them. Therefore, without delay, let's get started.

These instructions are suitable for any smartphone. In the process of creating a stand, you simply adjust the fasteners to fit its size.

What do we need

In order to implement our plans, we will need the following:

• a pair of paper clips;
• pliers;
• bank card (expired, of course);
• Super glue.

To make the building more attractive, we may also need additional design elements. This could be, for example, rhinestones, pieces of fabric or colored leather.

In addition, we can supplement the design with special corners - clips, which you have probably seen in cases - books for phones and tablets. They are made of rubber and glued to a plastic card.

Making a phone stand

So, after all the preparations are completed, you can proceed directly to the assembly. Let's look at it step by step:

1. Clear your workspace so that nothing interferes with the creation of the stand.
2. First, the paperclip needs to be slightly bent until its edges form an angle of approximately 70 - 90 degrees.
3. We bend the short edge of the paperclip so that it almost touches the first one. The end result should be something in the form of a loop.
4. Let's move on to working with the long part of the paper clip. We mark approximately half of it and bend it in the opposite direction from the short edge. And here you need to take into account one feature - make a mark in such a way that when the stand is placed on the table with the sharp end up, the long side (before the fold) coincides in height with the short one. And the second (long side) bends so as to completely adhere to a hard surface (table).

How to connect a speaker to a phone via Bluetooth

1. Now, at the short end, we bend the part with arrows using pliers so that we get a small side to stabilize our phone. For clarity, we have prepared a screenshot that shows everything.

1. When the first paper clip is ready, we create the second one in its likeness. It is important to make exactly the same element, otherwise stability will not be achieved.
2. Now we need to glue the card to the paper clips. This must be done carefully. Carefully try on the position of the card, observing all the rules of symmetry. The end result should be a flat device that doesn't warp when you put it on a table, rather than a lopsided stand that wobbles all the time when you put your phone on or off it.

You also need to glue wisely. Apply neither too much nor too little glue, wait a couple of seconds until it starts to dry, and then place the card and press it, holding it for a while. At the same time, the waiting time for the glue to dry and the time for holding the part in the pressed position greatly depends on the type of glue used.

After our stand is ready, we can decorate it a little, making it more attractive. To do this, you can take the following measures:

• The legs of the phone stand (and these are our paper clips) can be painted, for example, with nail polish. And the appearance of the stand will depend on what varnish you choose.
• The card itself is also easy to cover with some material. The result is not only a beautiful back panel, but also a softer back panel that won't scratch your phone.

You will see for yourself how the appearance of the device will change for the better and its quality depends only on your imagination and efforts.

Video instruction

Creating some kind of design is not an entirely simple task. In order to better understand the subject, we recommend that you watch the video in which the author clearly shows everything.

How to connect a headset to your phone via Bluetooth

Finally

This is where we finish our step-by-step instructions, and we recommend that you move on to practice and assemble your first stand from paper clips for your phone.

If you have any questions, we recommend asking them at x. We will definitely read them and, if necessary, help with advice.

What do we need

In order to implement our plans, we will need the following:

• a pair of paper clips;
• pliers;
• bank card (expired, of course);
• Super glue.

To make the building more attractive, we may also need additional design elements. This could be, for example, rhinestones, pieces of fabric or colored leather.

In addition, we can supplement the design with special corners - clips, which you have probably seen in cases - books for phones and tablets. They are made of rubber and glued to a plastic card.

Phone stand made from paper clips

Homemade iPhone stand

Having spent a considerable (and for some, astronomically enormous) sum on a phone with an Apple logo, you don’t want to shell out money again to buy expensive accessories for your phone. Many craftsmen, through their rich imagination, make an iPhone stand using very different objects.

A creative do-it-yourself stand is an opportunity to show originality and reuse some materials (which is especially important for nature lovers).

Office option

If you spend a lot of time at work in the office, your choice is homemade iPhone stands made from paper clips or clips. In addition, a hand-made pencil stand will look very elegant (to make it, you will also need a pair of pharmaceutical rubber bands).

Tip: For greater stability, use pencils with rubber tips.

Not the most practical, but one of the most common options is an iPhone stand prepared in the form of origami from thick paper or cardboard. It is possible to say that this is a one-time option, but at the same time, paper is something that is at hand at almost any time. Very sophisticated users also use banknotes for these purposes.

The plastic card holder has also proven itself well. Skilled users note that, in addition, the territory of turbulence during the flight does not create any problems for such a stand.

Home option

Among the household utensils, for comfortable watching a movie from an iPhone or working with a Bluetooth keyboard, the following are perfect:

• decorative or clothespins, you can easily make a beautiful stand out of them, quickly, simply and with your own hands;
• adhesive tape (choose a roll of the required size, glue the tip of the tape to the back cover of the smartphone and adjust the viewing angle);
• Lego cubes - they make a very stable and good-quality iPhone holder. It is possible to easily vary colors and change designs (it is also possible to make a rotating model);
• rubber toys, by cutting out the required recess with a knife, you have the opportunity to take a new toy for your gadget.

Rare version

If you don't belong to the generation that can only listen to music through iTunes and have a couple of old audio cassettes in your archive, you can use a plastic cassette case as an iPhone holder.

Hint: MiniDV cases are the perfect size

Other options

To minimize the effort spent searching for the necessary materials, you can use bright iPhone packaging. It goes without saying that this option is suitable only if you did not throw it away, but kept the plastic stand in which your phone was placed.

Again, it is possible to make a simpler option by simply cutting a hole at the desired angle, or spending half an hour to make an attractive vertical plastic holder with your own hands with the ability to access a USB cable (can be used while charging).

Remember to read the comments, there is also a lot of necessary information there. If your question is not answered, but later comments are answered, then the answer to your question is contained in the article, respect other people's time.

In addition, you may be very interested

Source: https://sms-taim.ru/life/podstavka-dlja-telefona-iz-skrepok.html

How to make a stylish phone stand out of a paper clip

Good day, dear readers! At least once, a situation has happened to you when your hands are tired of holding a smartphone, but there is no stand under your hands.

The fastest and cheapest way is to make such a design yourself. That's why we'll tell you how to make a phone stand out of a paper clip. Interesting to know? Then let's get to work!

Set of tools

So, all you need is nothing:

• Two paper clips;
• Pliers;
• A plastic card or something similar of the same size or smartphone size;
• Super glue.

In addition to this, you can create special clamps for the device so that it does not fall out of the structure, or secure it at the corners with rubber bands, as can be seen on many photo covers for tablets.

In general, there is room for your imagination to run wild.

From improvised means

When starting to sort through the objects that are at home, ordinary clothespins are sure to catch your eye. It seems like a thing that is useless in everyday life and will only be useful after washing, but this is not at all true. The video shows in detail how to make an original phone stand from clothespins.

You couldn't even guess that a phone stand can be made from a plastic card! This manufacturing method is one of the most basic. For this we only need a map. In any home, on tables, in wallets, there will definitely be at least one card that has not been used for a long time: an old discount card from another city, a discount card for a closed hairdresser, and so on.

We take such a card and make only the next two movements. First: put the card vertically and make a fold 1 or 1.5 cm thick, this fold forward will be the phone holder. The remaining part of the card is visually divided into two parts and bent in the very middle. Now we have a back. The downside of this stand is that the only position for placing the phone is horizontal. Although maybe for those who don’t need a vertical position, this will be a plus.

Article on the topic: Knitting for children: patterns for a suit, dress, jacket, hat and booties

To make your idea come out without any problems, watch the video on how to make unusual things from a card: