Gas lift for a bed with a lifting mechanism do-it-yourself repair

Do-it-yourself gas bed lift repair

Modern double beds are most often equipped with a lifting mechanism.

This system is called a gas lift; it ensures a smooth lifting of the bed along with the mattress into a vertical position. This feature of the beds makes it possible to remove them if necessary, which significantly saves space during the day. If the bed is in the bedroom, then with the help of such a mechanism access to the linen drawer is provided.

How to repair a lifting mechanism with your own hands

Sometimes the bed lifting mechanism, which is responsible for transforming the structure, breaks along with the slats. The following signs indicate a breakdown:

• spontaneous lowering of the orthopedic base;
• jamming of the mechanism when lifting or lowering the structure;
• creaking and other extraneous sounds that occur during operation.

If one of the listed symptoms appears, it is necessary to disassemble the lifting mechanism. To do this, the mattress is removed from the bed, after which its base is unscrewed. Then the fasteners are unscrewed, with the help of which the mechanism is screwed to the structure. It is difficult to repair such a product yourself and therefore it is better to take it to a specialist who professionally repairs furniture.

How does a gas lift work?

All gas lifting mechanisms consist of the following parts:

• metal plates made by stamping;
• metal axles;
• gas lift.

The principle of operation of such a mechanism is simple. Metal plates are attached to the bed and closet. When the berth is raised using a lift, the load is distributed around the metal axis. Thanks to this, no serious effort is required. Just a little pressure is enough to put the bed in the closet.

How to eliminate a squeak

It's uncomfortable to fall asleep on a bed that creaks. In addition, this unpleasant sound can irritate others. In houses with thin walls, even neighbors can hear it. To get rid of a problem, you need to determine the cause of its occurrence. Depending on the type of breakdown, eliminating squeaks in beds with your own hands is done as follows:

1. The frame of the product is carefully inspected beforehand. Pay attention to all connecting elements. If they are loose, they are tightened. Additionally, screws and bolts are lubricated with a furniture composition based on wax and soap. Excess gaps in the wooden frame of the bed can be eliminated using a cork seal. Additionally, it is recommended to use furniture glue.
2. Often the cause of squeaking is the springs of the mattress. Due to the constant load, they become unbalanced. You can correct the situation by turning the product over. If this does not help, then you need to replace the springs and purchase a new mattress. It happens that the product rubs against the frame of the bed and a squeak appears. The defect can be eliminated by preventing contact of the mattress with the wood.
3. An unpleasant sound is often produced by broken slats. If they cannot be repaired, then it is better to replace the incorrectly functioning elements.
4. It is also necessary to slightly rock the legs of the bed. In this case, creaking occurs in the area where the supports connect to the frame.
5. The cause of the unpleasant sound is defects in the supporting structure - cracks. If they are numerous, then it is better to replace the housing. Single damage is filled with furniture glue and reinforced with a metal plate.
6. The creaking occurs due to the fact that the bed is on an uneven floor. In this case, it is better to move the furniture to another place or replace the floorboards.

The simplest and most reliable way to eliminate squeaking is to update old parts. It is important to pay attention to the lifting mechanism.

Causes of failure

Often the cause of failure of these mechanisms is poor-quality parts. Therefore, when purchasing it, you should carefully choose the manufacturer. Manufacturers from Germany or mechanisms of German-Russian production are considered the best.

The cause of the malfunction may also be an incorrectly selected type of device. All gas lifts have parameters at which they are able to withstand a certain weight. When choosing them, you need to pay attention to this indicator.

If the lift is installed incorrectly, it will not be able to perform its functions fully. There will be no smooth movement, and you will have to make an effort to assemble the bed. If the fittings or parts of this mechanism break down, it will have to be completely replaced. The bed lift at pro100mebli.com.ua/product/gazovyy-podemni can be selected with any necessary parameters.

How to replace a lift

First of all, you need to choose a high-quality gas lift for the bed. Once it is selected, you can begin installing it:

1. It is necessary to dismantle the old equipment. To do this, you need to unscrew all the nuts and install new gas shock absorbers in the vacant space. The position should be cylinder up.
2. Installation must be done with the frame in the open position. First, attach the part that is to be installed on the bed frame, and then attach the mechanism to the frame.
3. It is necessary to ensure that all parts are securely screwed to the body.
4. After installing the mechanism, you need to check the smoothness of its operation.

To avoid problems with such a mechanism in the future, it is necessary to take into account its characteristics and the quality of the fittings. Then it will last a long time and will not cause any trouble.

Source

How does the lifting mechanism work?

Gas lifts come in two varieties with almost identical operating principles:

1. Automatic – when the bed is raised, the nitrogen in the cylinder expands. When gas pressure is applied to the piston, the rod attached to it pushes the surface of the bed upward. To slow down, a stop damper is used, which is an oil plug. The stopper allows you to move the bed smoothly.
2. Frictional - such a gas lift is not equipped with a damper and has a slightly lower nitrogen pressure. It differs from automatic by the ability to stop the surface of the bed at any angle.

The gas lift on the bed does not compress: reasons

The main reasons for gas lift failure include:

• Incorrect installation of the gas lift with the rod up, which causes a sharp jerk when lifting. As a result, the components of the equipment wear out much faster.
• Tightening the nuts during installation to the frame.
• The load on the mechanism was incorrectly calculated, for example, a gas lift of greater power than required was installed.
• Installation of cheap elements of unknown brands.
• Insufficient gas pressure in the piston.
• Lack of parts.
• Incorrect operation due to the use of force when lifting/lowering. By default, the lifter performs these processes independently. The user only needs to gently push up or press down on the surface.

Important! If you detect a creaking, too sharp or slow movement of the mechanism, you should immediately inspect it, and, if necessary, repair it yourself or call a specialist. Otherwise, the gas lift will soon have to be completely changed.

The nuances of repairing a bed at home, step-by-step recommendations

New furniture means comfort, coziness and aesthetic pleasure. But some 7-10 years will pass and your favorite bed or sofa begins to age: the wooden frame cracks in places, the upholstery tears, the foam base sags. Many owners are beginning to look at the bed differently and are thinking about replacing it.

Of course, you can buy new furniture, but you can also try to repair it. Repairing beds and sofas helps extend the life of once-loved furniture, as well as save money in the family budget. If you have the desire and a little knowledge, you can easily restore your furniture.

First you need to understand what is the cause of the breakdown.

What to do if a squeak appears

It is inconvenient to fall asleep on a creaky bed, and it also causes discomfort to those around you. It is impossible to accurately determine the location of this unpleasant sound. It can come from the base or partitions, metal connections of the product.

Basic measures to eliminate squeaking:

1. The first step is to determine the material from which the bed frame is made;
2. Check all connections. It is necessary to tighten the connecting elements: screws, self-tapping screws, bolts and nuts. For reliability, they can be treated with a special furniture compound. Wax and soap can also serve as a replacement for this composition;
3. Carefully inspect the mattress, especially the spring one. The cause of the unpleasant sound may be springs;
4. If lamellas are used instead of springs, then broken elements can be easily replaced with new ones;
5. Particular attention should be paid to the legs at the base of the bed. Now the choice of legs is huge and choosing the right ones will not be difficult;
6. If squeaking is caused by boards lying too close to each other, there are several options for eliminating it - the boards are swapped, the base is turned over, or the contact points are treated with lubricant.

The most successful and 100% way to get rid of squeaking in connecting elements is to replace old fasteners and assemblies with new ones. And it is not necessary to call a specialized company for help for these purposes; you can independently repair the bed at home.

Purchasing furniture and choosing it is a truly difficult and responsible task. To avoid creaking, buy reliable metal products and forged models of bed bases.

Checking the connecting fasteners

Then - mattress springs

You should check for creaking lamellas

Then the legs

Restoration of children's upholstered furniture

If a child's bed is broken, it should be repaired immediately, because deformation of the surface of the bed will eventually affect the child's health, posture and well-being.

The places in children's beds that most often fail can be:

• Lifting mechanism in a sliding or built-in bed;
• Wooden partitions of the base and the frame itself due to normal wear and tear of the material or any external mechanical influence;
• Fragile decorative legs installed on furniture under strong impact (intensive play by children, jumping on the bed);
• Poor quality mattresses and product deformation, which negatively affects the child’s health;
• Additional elements: armrests, drawers and sections.

Advantages and disadvantages

Advantages of a gas elevator:

• ease of operation;
• silent raising and lowering of the surface;
• when using liquid nitrogen in the shock absorber, the metal parts of the bed do not rust and the rubber gaskets do not deteriorate;
• convenience and ease of use (no effort required, as is the case with spring furniture);
• reliability (rare breakdowns of gas lifts);
• minimal risk of injury - moving parts are hidden under the casing;
• a wide range of.

The gas lift mechanism allows you to fold and unfold the bed about 20 thousand times, which is an approximate service life of several decades.

Flaws:

• unaesthetic appearance of the bed - gas lifts are partially visible;
• It is impossible to immediately determine the quality of the parts.

The conditional disadvantage of gas lift is the high price . However, it is compensated by a longer service life provided that it is installed correctly.

Negative aspects of using this device in beds:

• Lack of aesthetics. Some bed models are designed in such a way that the gas lift is noticeable at the head of the bed.
• Low-quality materials used in the production of such a mechanism, in most cases, become unusable after some time. But in some cases it is impossible to determine the quality of parts when purchasing.
• The high cost of a bed with such a device.

Advantages of lifting beds

Compared to standard beds, lift-up models are practical, multi-functional and ergonomic. Such designs are convenient to use in limited areas. They have a spacious interior space where you can store bed linen, home clothes, bedspreads, pillows and blankets.

Other advantages include:

• high reliability and durability;
• easy to use;
• dust and dirt do not collect under the bed;
• saving money when purchasing;
• different configurations.

When choosing a bed, it is important to consider not only the quality of the product itself, but also the lifting mechanisms. If the installed elements are not the best, you can replace them with gas ones. They are more durable and provide long-term and comfortable use of the bed.

How to fix the bed lift mechanism?

Options for lifting mechanisms for beds, nuances of operation.
For apartments, especially small ones, the real problem is the lack of free space. Therefore, their owners are looking for any ways to save usable space. A lifting mechanism for the bed can be of great help in this, the use of which will free up part of the living space. Let's consider the characteristics of different designs of lifting mechanisms and beds. The purpose of the mechanisms. Lifting mechanisms allow you to expand the functions of beds and thereby free up part of the living space of the house. Two methods are used for this. The first makes it possible to move the bed into a vertical position and put it in the closet. Or you can transform it into another piece of furniture for the time when the bed is not in use, thereby freeing up scarce living space. The second method adds the ability to the bed to store household items, linen and clothes.

bed gas lift repair

The box for it is placed under the rising bed. This solution can eliminate the need to purchase a linen closet, saving money and the bedroom space that would be required to install this piece of furniture. Beds with lifting devices have some other useful qualities: They carefully store things - the sleeping place closes the box very tightly and does not allow dust to pass through, They have an aesthetic appearance - bedding can be put away in the box without any problems and the sleeping place looks very aesthetically pleasing, They make cleaning easier - under such the bed does not accumulate dust and it will always be clean. To lift and hold the berth, special mechanisms are installed.

Varieties. There are three types of bed lifting devices: Manual. This is the simplest lifting mechanism for a hinged bed.

The principle of its operation is based on the use of human physical strength, because it does not contain power units that compensate for the weight of the raised bed. The advantages of manual mechanisms: low price, strength and reliability. It is not recommended to install manual lifting mechanisms on beds for children.

The child may not be able to cope with unfolding the bed on his own and may be injured. Spring-loaded. As a lift, such mechanisms use twisted springs, which take on part of the load and significantly facilitate the transformation of the bed. If it is necessary to reduce the force of the mechanism, it is enough to remove the springs, but it is impossible to increase it. Over time, the springs gradually stretch, the connections wear out, and eventually the mechanism has to be replaced. On gas shock absorbers.

This lifting mechanism is the most comfortable because it takes on the entire load when lifting the bed. This quality allows women, teenagers, and people with disabilities to use beds with this mechanism. This bed lifting mechanism uses a gas shock absorber as a power unit. It consists of a cylinder filled with nitrogen under high pressure, an oil damper and a piston with a rod. The gas shock absorber mechanism consists of: Metal plates and angles, Steel axle, Gas lift. Plates and corners are attached to the berth and to the sides of the box. When lowering, the plates rotate on the axis and the gas elevator is compressed under the pressure created by the weight of the berth.

When lifting, the force of gas pressure pushes out a piston with a rod, which smoothly moves the stock to a vertical position. The power of gas elevators is indicated in Newtons (N). Beds require mechanisms with a power from 600 N to 2200 N. The only disadvantage of a gas lift is its high cost, which, however, is justified by its ease of use and durability. Dimensions and characteristics. Beds differ from each other in several characteristics, each of which is important when choosing the optimal option for a bed lift. Dimensions. Length – the standard length of beds for adults ranges from 200 to 220 cm, for children – from 120 to 190 cm.

Width – depends on the number of beds. Children's beds have a width of 60-70 cm, single beds 90-100 cm, the standard width of double beds is from 120 to 160 cm. The height is chosen so that it is easier for its users to lie down and get up (for children - lower, for older people - higher ). Combinations of length and width within the specified limits can be very different and are chosen depending on the desires of those who will sleep on it. Beds measuring 160x200 cm and having a lifting mechanism with a gas lift can be considered the standard for double models. All these parameters influence the choice of lifting device only in combination with other characteristics.

The weight of the sleeping place is mainly influenced by the mattress. There are a lot of varieties of its fillers and their weight can vary significantly. The weight of the part of the bed being lifted is a major factor in determining the type and power of the lifting mechanism required. For example, for lifting a double bed with an orthopedic mattress, a spring mechanism is not very suitable, not to mention the manual version.

And for a single bed with a foam mattress, the use of an expensive gas mechanism would be unjustified. Design. Beds with a lifting mechanism have two types of design - with a horizontal lift of the berth and with a vertical lift of the entire bed (wardrobe bed). You can raise the bed in two ways - by fixing the box parallel to the horizontal level at a certain distance from it, or by opening it like a book, from the foot of the bed. In addition to the foot, any side of the bed can also be raised if you install the lifting mechanism a little differently. A side lift is needed in cases where, for reasons of optimal placement, it is decided to place the bed sideways close to the wall.

All options require symmetrical installation of two lifting devices of the same type on the box. For a single version of this design, any lifting device is suitable. In double beds, as a rule, gas lifts are used, regardless of the weight of the bed.

There are also two options for lifting the wardrobe bed. The bed is raised either by the foot or by the side. In both cases, the transformation can be done with very little effort if the lifting mechanism of this bed uses a gas lift. But its power for each single-bed version will be different. When lifting from the side, it is possible to use a spring lift. A manual device is usually not used for this design. Installing a very powerful gas lift on a bed is not recommended, since in this case it will be very difficult to lower or raise the frame.

You can roughly determine the required power at the rate of 10 N per 1 kilogram of the weight of the structure being lifted. When choosing the type of lifting device, you need to take into account three more factors: Mode of operation - regular lifting of the bed or occasional, Physical capabilities of the person who will sleep on it, Cost of the lift - the cost of different types of lifting devices differs by an order of magnitude, so not every user will be willing to pay money for an expensive lift unnecessarily. Rules for safe use. When using lifting beds, you should follow simple safety rules: The wardrobe-bed in a vertical position must be securely fastened to the wall, When raising and, especially when lowering beds, it is recommended to stand to the side of the structure, When using a device with a spring shock absorber or a manual one, the berth in the raised position it must be additionally secured with a special support. Gas lifts are considered the safest. They hold the bed securely in the raised position because the piston of the gas elevator is fully extended and in this state it cannot contract spontaneously. Some companies offer a gas lift lock on the gas spring rod in the kit, but this is for overly cautious buyers.

In principle, the bed cannot fall down sharply. Even if one gas lift suddenly fails, the bed will slowly lower due to the second one. Reliability. All bed lifting mechanisms have a fairly high level of reliability. But here we need to make a reservation - this applies to products from manufacturers who occupy leading positions in the market for these devices and have earned the trust of customers. For example, the best gas elevators are considered to be German, and spring devices are Italian. In spring lifting mechanisms, the main load falls on the spring itself, which leads to its wear.

How to select, assemble, install and press by hand?

Since the operation of the bed is required to be reliable and long-term, you need to choose the right mechanism. It is necessary to calculate the load that it will withstand. To calculate, you need to find out the weight of the structure, take into account the density of the material of the bed and mattress (characteristics are noted by the manufacturer).

Gas lifts have different markings, indicated in Newtons:

1. Approximately 10 N can support 1 kg of weight.
2. Step marking – 200 units (600 N, 800 N, etc.).
3. The load must be distributed evenly. It is recommended to install 2 devices on both sides of the bed.

As an example, we can imagine that a gas lift needs to be installed on a bed, the weight of which together with the mattress is 60 kg.
This means that two mechanisms are needed with a minimum marking of 600 N. Theoretically, two elevators will lift 120 kg of mass, but given the distribution of force at an angle, this does not happen. The device is chosen with a small margin, since during active use it weakens. You should not install an overly powerful gas lift on the bed - raising or lowering the frame will require a lot of effort.

To install the mechanism yourself, you will need to prepare tools such as:

The installation algorithm is as follows:

1. The furniture body on which the device is planned to be installed is assembled. To securely fix the elements and strengthen the entire structure, metal corners are used.
2. The gas elevator is screwed to the body using self-tapping screws. They are included in the mechanism kit. 4 holes are drilled in the housing for fasteners. The lower part is fixed with bolts, then the corner plate of the gas elevator is screwed on. The device is screwed down, fixing the surface of the bed in a raised position to avoid damage to the mechanism due to errors in calculating the length of the arm.
3. The surface of the bed is lowered onto the base of the frame, in which 4 holes are drilled to secure the upper part of the mechanism. The drilling points must be correlated with the location of the fixed bottom strip.
4. The frame is lifted and the bolts are screwed into the upper part of the gas elevator.
5. The assembly is completed by connecting all parts of the gas lift with a piston, fixing it from the bottom and top of the mechanism.
6. After installation, check the serviceability of the gas shock absorber: compress and release it several times. The movement of the gas elevator should be silent and soft.

How to install correctly?

Installing such a lifting device is quite simple. To assemble it correctly, you must follow our recommendations.

Below are the steps for such an assembly:

• First you need to use a drill to make 3-4 holes for fasteners on the box.
• The lower part of the device is secured with bolts.
• We attach the corner of the lifting mechanism to this structure.
• It is necessary to lower the base into the frame. We drill 3-4 holes on all sides, taking into account the position of the bottom bar.
• Leave a gap of 5-10 mm between the box and the frame, then tighten the bolts on the upper structure.
• We connect everything together using pistons, securing them to the top and bottom of the device.

See below for the gas lift installation process.

Before installing the system on furniture, it is necessary to check the prefabricated structure. It should not lower itself spontaneously, nor should it creak or jam during the lifting process.

Specifications

If the bed is equipped with a gas lift, the surface of the product can be easily raised and returned to its original position. Everything will go smoothly and without unnecessary noise. The main characteristics of such lifts are:

1. The main substance that ensures the functionality of the structure is inert gas (most often the cylinders are filled with nitrogen).
2. The chamber, rod and support tips are made of steel.
3. The minimum thickness of the walls of the cylinder, which is filled with gas, must be 1 mm, otherwise it will be unsafe to use the structure.
4. Any gas elevator can be compressed by applying force.
5. For the device to function properly, the room temperature must vary between -30/+70 degrees.

How to choose an adult and children's mattress for a bed, tips for housewives

It must be taken into account that the pressure in the cylinder is very high. That is why, if an element is deformed or another malfunction is discovered, it is strictly not recommended to disassemble it and try to repair it yourself. Below is a table showing the calculation of forces for vertical beds.

If you purchased a horizontal type bed, the power of the lift should be different. This is due to the fact that the load in this case is distributed differently. For horizontal beds, you can use less powerful gas elevators.

If a person does not know how much a bed weighs, one can be guided by average values. A single design weighs about 30 kg. The weight of an orthopedic mattress varies from 30 to 40 kg. Therefore, a single bed weighs on average about 60 kg.

How to properly remove a gas shock absorber?

Removal of the gas lift from the mounting points is carried out with the utmost care so as not to damage the cylinder.
Before unscrewing and removing the gas lift, it is fixed in the open position. Due to the high pressure inside the cylinder, the gas elevator must not be compressed, bent, heated, opened or drilled.

The removed gas lift must be protected from exposure to dyes, dust, chemicals, mechanical shocks, and scratches . Such impacts will lead to deformation of the rod seals, which will reduce the performance and service life of the gas shock absorber.

If the presence of negative factors in the design cannot be avoided, possible damage is minimized with an additional protective tube - a cover for the rod.

Device and installation

A gas lift is a bracket that raises and lowers the door of a wall cabinet and locks it in the open position. This kitchen mechanism consists of the following elements:

• housing, with nitrogen;
• a rod moving along the body;
• bearings that ensure uniform movement of the rod;
• parts that maintain tightness: bushing, oil seal, boot, sealing element;
• fastening parts.

The rod is attached to the door using all the auxiliary elements. There are different versions. If installed incorrectly, distortions may occur. In this case, not only aesthetics are lost, but also the functional mechanism will not provide its purpose. Before installation, you need to mark the fasteners. The mechanism must match the design of the cabinet. So, if its internal space has a height of 365 mm, then the gas lift should have a length of 355 mm.

Installation of the lifting mechanism

When planning to assemble the Suspa device, you should familiarize yourself with the basic recommendations of the manufacturer of this hardware. The gas lift installation process can be divided into several successive steps:

• First, the bed frame is assembled. When performing all operations, follow the manufacturer's instructions. Metal corners are used to connect the boards. This will strengthen the entire structure and make it more resistant to external influences.
• When the frame is assembled, they begin to attach the gas lift. The structure is fixed using special self-tapping screws, which are often included in the kit. Please note that some gas lifts are one-sided. Therefore, it is important not to confuse them.

In some cases, the side of the cylinder also plays an important role. This specification should be clarified with the manufacturer.

• At this stage, the folding frame is assembled. In some cases it is metallic and solid. If the structure is made of wood, then it is constructed in accordance with the manufacturer’s instructions.
• The procedure is completed by attaching the gas lift to the upper element. It is important to screw the mechanism only when the lid is open . This will eliminate the possibility of breakage due to incorrect calculation of the arm length. When the entire structure is assembled, you should run the system several times to check its functionality. If the system does not work properly, the mechanism should be reinstalled.

Installing gas lifts on a bed can differ in many nuances. If you are not sure that you can perform the operation efficiently, you should entrust it to an experienced specialist. The best option would be to make such furniture to order. This will allow you not only to select the size and style of the structure, but also to determine the optimal characteristics of the lifting mechanism.

If you still want to handle all the work yourself, consider important nuances. This way you can get better results. To learn how to install a gas lift, see the following video.

How to check the work?

After installing the gas elevator, the surface of the bed is raised and lowered several times to check the operation of the device. When the mechanism is installed correctly, lifting and lowering occurs easily, smoothly, silently, without jamming.

If difficulties arise with operation, the cause should be sought in faulty fittings or installation errors.

The gas shock absorber is simple in appearance, but requires careful attention to installation and operation. It should be installed extremely carefully and competently. Correct installation of the mechanism will allow you to use the furniture for a long time without worrying about safety and reliability.

How to repair a gas lift bed yourself

Independently identifying defects in the operation of the piston mechanism requires some knowledge and skills, otherwise eliminating the malfunction will end very badly.

To understand the reason for the poor quality of the gas lift, you need, at a minimum, to arm yourself with the manufacturer’s instructions. Or you can watch videos on the Internet on this topic.

The algorithm of actions includes the following steps:

• It is necessary to make sure that the load and power thrust of the mechanism correspond. This item mainly applies to newly purchased models. It is important to understand that the gas lift only works correctly at full load. Therefore, it is imperative to place a mattress on the base.
• Visual inspection of the correct installation of the mechanism. If necessary, completely or partially dismantle it, adjust the elements relative to each other, loosen/tighten the fastening parts.
• Complete replacement of low-quality fittings without identification marks with proven ones from well-known brands.

If, as a result of the operations performed, the result remains the same, it is recommended to contact a specialist.

How to repair it yourself

If the gas lift has stopped working and the mechanism needs to be repaired, to do this it is necessary to establish the true cause of the breakdown.

1. First of all, you need to pay attention to the weight of the structure, since with a small load the mechanism will not work. The spring is compressed in the structure only under full load conditions.
2. Elimination of errors made during the assembly process is carried out by dismantling the entire structure. Re-installation is carried out taking into account the correct selection (adjustment) of parts to each other.
3. The quality of the fittings influences the good functionality of the bed. Therefore, for gas lift installation, it is better to purchase spare parts from trusted manufacturers.

Important! When installing and repairing, you should use the manufacturer's instructions.

In order to make repairs yourself, certain skills and knowledge are required, the absence of which can lead to poor quality work. To ensure that basic repairs do not spontaneously become major repairs, you need to contact experienced craftsmen to do the repairs.

Is it possible to fix a gas lift with your own hands?

Repairing such a part of the structure of any chair is not justified due to the high cost of repair labor - it is easier to replace it with a new one than to repair the old one. But, if you don’t want to waste time on a new mechanism, you can try to fix the problem yourself. This does not require special skills or knowledge - just follow the instructions.

The Ukrainian manufacturer Barski provides all its customers with a 5-year warranty on mechanisms and 2 years on upholstery materials. There are no similar offers on the market. In addition, the main misconception of the consumer is that the warranty cannot be “knocked out”; this judgment does not apply to the manufacturer Barski - all breakdowns due to the manufacturer’s fault are eliminated after the consumer’s request.

How to repair it yourself

If the gas lift has stopped working and the mechanism needs to be repaired, to do this it is necessary to establish the true cause of the breakdown.

1. First of all, you need to pay attention to the weight of the structure, since with a small load the mechanism will not work. The spring is compressed in the structure only under full load conditions.
2. Elimination of errors made during the assembly process is carried out by dismantling the entire structure. Re-installation is carried out taking into account the correct selection (adjustment) of parts to each other.
3. The quality of the fittings influences the good functionality of the bed. Therefore, for gas lift installation, it is better to purchase spare parts from trusted manufacturers.

Important! When installing and repairing, you should use the manufacturer's instructions.

In order to make repairs yourself, certain skills and knowledge are required, the absence of which can lead to poor quality work. To ensure that basic repairs do not spontaneously become major repairs, you need to contact experienced craftsmen to do the repairs.

What is a gas lift?

Installing a gas lift on kitchen furniture ensures the correct and smooth functioning of any piece of furniture in the kitchen. What is gas lift? To fully understand this issue and learn how to properly install a gas lift, it is worth determining that a gas lift is a shock-absorbing mechanism that is intended for doors that open horizontally. In other words, this is a cantilever supporting part, a holder that fastens protruding horizontal parts on a vertical surface.

This is a sealed unit filled with nitrogen. When nitrogen gets inside the cylinder during use, it will be impossible to repair such a breakdown.

Source